Cable blowing machines for mini cables Ø 4-12 mm

1 | New Product – IntelliJet for micro- and mini-cables – complete new device

The first semi-automatic cable blowing unit with blowing assistant and electronic blowing data memory. Now in series production.

The new IntelliJet is a pioneering, intelligent blowing system that facilitates the blowing of fibre optic mini cables for the operator and improves installation quality. Cable layers as well as clients benefit from these improvements.

At the heart of the innovation is the measurement, presentation and control of the pushing force, which is transferred onto the cable by the drive system. The pushing force is constantly verified against the maximum permissible pushing force, which is determined through the crash test, and which will be specified in the cable data sheet in the future. A second assistant monitors the cable slippage. Both assistants give the operator an indication as soon the blowing procedure approaches a critical range and provide information on counter-measures. If the critical range is exceeded, the blowing unit stops. In this way, damage to cables can be avoided, the responsibility of the blow-in operator is relieved and the blowing quality is increased.

A clear blowing log with an electronic data transfer completes the new system. The new IntelliJet not only helps meet the minimum requirements for automatic logging of Deutsche Telekom but also the far-reaching demands for automated blowing processes. In addition to the new device, the IntelliJet can also be created from the tried and tested „MiniJet” blowing unit by means of an upgrade. With the IntelliJet, sustainability for further automation levels is also guaranteed. The main benefits for cable layers are:

Operators with little blowing experience can also achieve optimal blowing results with sensitivity and technical skill – the problem with the currently tight labour market can thus be alleviated.
The two blowing assistants indicate critical operating conditions and stop the blowing procedure before damage to the cable occurs.
Time savings for the blowing team and in order processing thanks to automatic data logging, archiving and electronic transmission.
The logging of blowing parameters can provide evidence of bad subduct routes and is thus a basis for legitimate variation orders.
The handling on the construction site is simple and nearly identical to current work with the MiniJet.
Customers also benefit from the use of the IntelliJet:
The automation of the blowing process will improve blowing performance and quality and reduce damage to cables, which increases the efficiency of FTTx projects.
Precise and clear logging of the agreed blowing performance facilitates the error detection, financial settlement and data archiving.
If damage to cables occurs at a later point, the original blowing log provides a reference for the blowing-out capability of the cable and can thereby reduce the repair time required (simplification of crisis scenario).
Always both positions IntelliJet (Pi 02 OB) and IntelliBox (IBN 02) must be ordered!

,Fiberoptic-fibreoptic-blowing-machines,Cable-blowing-equipment,Cable-coiler-uncoiler-unwinder,Duct-pipe-calibration-set,Appareile-souflage-fibre-optiques,Enrouleur-dérouleur-bobines,Jeux-calibrage-conduit-tube,Aparatos-soplar-cables-fibra-ópticas,Aparato-intermediario-soplar-cables

Code	Type	C-D	Duct-D	Air-supply	Push							kg
424302	PI 02 OB	4-12	8-40	16 bar/5 m³/min.	300 N							47,00
424342	IBN 02											13,00

2 | Upgrade of customer MiniJet P01 and P02, from 2011

A customer MiniJet of the P01 and P02 (from 2011) series can be upgraded at Vetter to the IntelliJet version. An „upgrade” machine such as this has no disadvantages compared with the new device when put to practical use on the construction site.

Upon customer request, during this upgrade the condition of the MiniJet can also be checked at the same time, a maintenance offer issued, if necessary, and carried out on acceptance of the service. In this way, the overhauled, newly upgraded IntelliJet blowing unit will once again be well prepared for the upcoming challenges of the various blowing projects.

Always both positions IntelliJet Upgrade Set (PIU OB Upgrade) and IntelliBox (IBN 02) must be ordered!

,,,

,Fiberoptic-fibreoptic-blowing-machines,Cable-blowing-equipment,Cable-coiler-uncoiler-unwinder,Duct-pipe-calibration-set,Appareile-souflage-fibre-optiques,Enrouleur-dérouleur-bobines,Jeux-calibrage-conduit-tube,Aparatos-soplar-cables-fibra-ópticas,Aparato-intermediario-soplar-cables

Code	Type	C-D	Duct-D	Air-supply	Push							kg
424330	PIU OB Upgrade	4-12	8-40	16 bar/5 m³/min.	300 N							3,10
424342	IBN 02											13,00

3 | MiniJet for Fibre Optic Cables

MiniJet, further development of the CableJet and MicroJet. For blowing-in mini fibre optic cables in long distances. Long and soft pneumatic belt drive especially for delicate cables. Produces high daily output. Electronic length and speed meter. Without cable and duct inserts. accessory and technical details see below.

Very careful but high power transmission to the cable through the soft belts.
Suitable excellent for very long cable distances with complicated design.
Simple control, high safety for operator and for cable.
Small dimension of 635x400x255, weight of the machine only 21,6 kg
For compressed air to max. 16 bar, airflow to 5 m³/min.

,,,

Code	Type	C-D	D-OD	Air max.	Push							kg
420100	P 02	4-12	8-40	16 bar/5 m³/min.	300 N							41,00

4 | Accessory-set for MiniJet

accessory-set for MiniJet P 02. All cable and duct inserts for a certain cable and duct diameter range, see below.

,,,

Code	Type	C-D	In duct-D	kg
420130	SET 40-83	4,0-8,3	10 + 12	0,57
420140	SET 84-124	8,4-12,4	14 + 16	0,56

5 | Duct inserts

Duct inserts for MiniJet for bigger duct of D 20-40 mm.

,,,

Code	Type	D-OD	kg
420228	REM 20	20	0,20
420230	REM 25	25	0,20
420232	REM 32	32	0,20
420240	REM 40	40	0,20

6 | Duct sealing for MicroJets and MiniJets

Duct sealing, sets of 6 pcs. suitable for cable blowing machines and duct-diam. according to table shown below.

,,,

Code	Type	D-OD	For device	Set	kg
42230167	RAD 07	7	PRM196/EM25/P02	6	0,01
42230168	RAD 08	8	PRM196/P02	6	0,01
42230170	RAD 10	10	PRM196/P02	6	0,01
42230172	RAD 12	12	PRM196/P02	6	0,01
42024014	RAD 14	14	PRM196/P02	6	0,01
42024016	RAD 16	16	IntelliJet/MiniJet	6	0,01
42024020	RAD 20	20	IntelliJet/MiniJet	6	0,01
42024025	RAD 25	25	IntelliJet/MiniJet	6	0,01
42024032	RAD 32	32	IntelliJet/MiniJet	6	0,01
42024040	RAD 40	40	IntelliJet/MiniJet	6	0,01

7 | Cable sealing

Cable sealing, sets of 6 pcs. suitable for cable blowing machines and cable-diam. according to table shown below.

,,,

Code	Type	C-D	For device	Set	kg
42230147	KAD 43	3,4-4,3	PRM196/P02/NBK483	6	0,01
42230149	KAD 53	4,4-5,3	PRM196/P02/NBK483	6	0,01
42230151	KAD 63	5,4-6,3	PRM196/P02/NBK483	6	0,01
42230152	KAD 70	6,4-7,0	PRM196/P02/NBK483	6	0,01
42230154	KAD 77	7,1-7,7	PRM196/P02/NBK483	6	0,01
42230156	KAD 83	7,8-8,4	P 02 / NBK 483	6	0,01
42021509	KAD 107	8,4-10,7	P02 / NBK812	6	0,01
42021511	KAD 124	10,8-12,4	P02 / NBK812	6	0,01

8 | Lubricator L 9 – automatic device

Lubricator L 9 for continuous greasing of the cables blown by MicroJet, MiniJet and UltimaZ. Performance and techn. details see below.

The Lubricator guarantees an uniform lubrication on the whole length duct length.
To mount on MiniJet there are adapters, see below.
In the Lubricator is included an adapter for the MicroJets EM 25, PR 140 and PRM 196

,,,

Code	Type	Suitable to	C-D	D-OD								kg
423500	L 9	MiniJet+MicroJet	1-9	4-16								2,20

9 | Lubricant for FOC

Micro Jetting Lube, lubricant for blowing-in fibre optic cables. Excellent lubricating effect. Adheres to the duct wall and leaves the cable nearly dry, an advantage for over blowing and working in cascades with further blowing machines. Consumption approx. 10 ml per 1000 m at duct-ID 10 mm. For other duct-ID analogue

For lubrication unique and ultimate classification, Water pollution class – non-hazardous, acc. to VCI-Conception. Safety data sheets are available.

,,,

Code	Type	Pack. drums	kg
234975	MJL 240	1 bottle 0,24 l	0,32
234977	MJL 424	24 bottles 0,24 l	7,50

10 | Duct cleaning sponge

Sponge for sub duct cleaning and pre-lubricating prior to cable blowing

,,,

Code	Type	D-OD	D-ID	Cellular	Qty.	kg
275398	RSM 04	7	4	D 8×30	20 pcs.	0,01
275400	RSM 06	7-10	5-6	D 12×30	20 pcs.	0,01
275402	RSM 08	10-12	8	D 16×50	20 pcs.	0,02
275404	RSM 10	12-16	10-12	D 20×50	20 pcs.	0,03
275406	RSM 16	20	15-16	D 32×50	20 pcs.	0,06

11 | Intermediate cable blowing head

Intermediate blowing head for finishing the left loops after blowing in two direction. Without duct inserts, without cable sealing. Max. pressure 16 bars.

,,,

Code	Type	C-D	D-OD	kg
275700	NBK 483	3,4-8,3	7-16	1,40
275703	NBK 812	8,4-12,4	12-20	1,50
275710	DAP 08	Air connector	for NBK 483	0,50
275712	DAP 11	Air connector	for NBK 812	0,73

12 | Duct inserts for Lubricator and intermediate blowing head

Duct inserts with 2 sealing for Lubricator and intermediate blowing head for duct-D see table below.

,,,

Code	Type	D-OD	For device	kg
423530	RES 4	4	Lubricator L 9	0,04
423532	RES 5	5	Lubricator L 9	0,04
423534	RES 7	7	Lubricator L 9	0,03
423536	RES 8	8	Lubricator L 9	0,03
423538	RES 10	10	Lubricator L 9+Intermed. blowing head	0,03
423540	RES 12	12	Lubricator L 9+Intermed. blowing head	0,03
423542	RES 14	14	Lubricator L 9+Intermed. blowing head	0,03
423544	RES 15	15	Lubricator L 9+Intermed. blowing head	0,03
423546	RES 16	16	Lubricator L 9+Intermed. blowing head	0,03
423548	RES 20	20	Intermediate blowing head	0,03

13 | Duct single sealing to intermediate blowing head and Lubricator

Duct single sealing to intermediate blowing head and Lubricator, for ducts-D see table below.

,,,

Code	Type	D-OD	For device	kg
042353801	RDL 4	4	Lubricator L 9	0,01
042353802	RDL 5	5	Lubricator L 9	0,01
042353803	RDL 7	7	Lubricator L 9	0,01
042353804	RDL 8	8	Lubricator L 9	0,01
042353805	RDL 10	10	Lubricator L 9+Intermed. head	0,01
042353807	RDL 12	12	Lubricator L 9+Intermed. head	0,01
042353809	RDL 14	14	Lubricator L 9+Intermed. head	0,01
042353810	RDL 15	15	Lubricator L 9+Intermed. head	0,01
042353811	RDL 16	16	Lubricator L 9+Intermed. head	0,01

14 | High pressure test

The new pressure test device combines three test methods in one electronic device. General test rules” individual selectable acc. requirements from the customer – The requirement from Deutsche Telekom acc. „ZTV-TKNETZ 40” – The low-pressure test acc. EN 1610:2015 as well as worksheet DWA-A-139:2009

The high-pressure test is presently the most frequent test method in the range of pressure tests for protective ducts. This test method will be performed at thick-walled protective ducts and subducts (micro ducts). With regards to the protective ducts, ducts with OD 50/40/32 mm are most frequently used application. For subducts a wider range of ducts can be tested from 7×1,5 until 20×2,5 mm. The high-pressure test distinguish between two different targets:

Verification of optimal blowing-in performance, which is guaranteed only by a pressure-tight duct system (short-term target)
Assurance of pressure-tight duct, the joints and connectors against water intrusion and the subsequent intrusion of soiling with sand. This results in incrustations, which causes problems during the blowing-in process and possibly later at blowing-out of cables (long-term target)

,,,

Code	Type	Explanation										kg
231700	High pressure	See the following devices										0,00

15 | High and low air pressure testing devices

The DPG 17U Universal pressure test device for test of cable ducts with regards to protective ducts and subducts working in the range of 0…7 bar. The operation is made by a 7″ colour-graphic-touch display. The new device support the user through a simple and menu-driven operation. With the help of a matrix (table) three different test methods can be selected. Those are „General test rules” individual selectable acc. requirements from the customer, the requirement from Deutsche Telekom acc. „ZTV-TKNETZ 40” and the low-pressure test acc. „EN 1610:2015”. This results in a maximum support for the user.

The result of the pressure test is summarized in a clear test protocol with three core areas. The test protocol will be stored on the device and can be loaded by a USB-interface to a customary PC.
The left shown 1. protocol shows a passed test „Test criteria fulfilled”
The left shown 2. protocol shows a failed test „Test criteria not fulfilled”

Upper area: General data like: Contracting company with name of operator, construction site, duct, temperature, times, measurement data with calibration status
Middle area: Result of the pressure test through colour-marked message: „Test criteria fulfilled” or „Test criteria not fulfilled”
Lower area: Graph with the two phases settling time and main test

,Duct-pipe-calibration-set,Duct-pipe-pressure-test,Système-calibrage-conduit-tube,Test-d’étanchéité-conduit-tube,Calibración-conductos-tubos,Comprobación-de-impresión,Estanqueidad-conductos-tubos

Code	Type	Designation	Press.	Application								kg
231740	DPG 17U	Universal pressure test device	0-7 bar	Cable conduits								6,40

16 | High air pressure testing NE2 and NE3

Pressure test distribution units for high-pressure tests of 1 duct acc. network level NE2 and NE3.

This test method will be performed at thick-walled protective ducts and subducts (micro ducts). With regards to the protective ducts the 50×4,6 duct is the most frequently used application. For subducts a wider range of ducts can be tested from 7×1,5 until 20×2,5 mm. For the connection of the ducts the right accessories have to be used to perform the test.

,,,

Code	Type	Designation	Connections	Press.								kg
23163007	DPV 1	Air distribution	1	0-10 bar								11,30

17 | High air pressure testing NE2 and NE3

Pressure test distribution units for high-pressure tests of 1-4 ducts acc. network level NE2 and NE3.

This test method will be performed at thick-walled protective ducts and subducts (micro ducts). With regards to the protective ducts the 50×4,6 duct is the most frequently used application. For subducts a wider range of ducts can be tested from 7×1,5 until 20×2,5 mm. For the connection of the ducts the right accessories have to be used to perform the test.

,,,

Code	Type	Designation	Connections	Press.								kg
2316293	DPV 4	Air distribution	4	0-10 bar								43,00

18 | High air pressure testing NE3

Pressure test distribution units for high-pressure tests of 1-12 ducts acc. network level NE2 and NE3.

This test method will be performed at thick-walled protective ducts and subducts (micro ducts). With regards to the protective ducts the 50×4,6 duct is the most frequently used application. For subducts a wider range of ducts can be tested from 7×1,5 until 20×2,5 mm. For the connection of the ducts the right accessories have to be used to perform the test.

,,,

Code	Type	Designation	Connections	Press.								kg
231680	DPV 12	Air distribution	12	0-7 bar								52,00

19 | Reducing coupling for high pressure test

Reducing coupling D 10-7, with duct 10×2/100, for D-OD 7 mm, for coupling subduct OD 7 mm with pressure test distribution units DPV 12, necessary to order 275750 DAK 10.

,,,

Code	Type	D-OD	Press.									kg
231686	AKR 07	7 mm	0-7 bar									0,02

20 | Air connectors for calibration sets

Air connectors for subduct calibration sets and for high pressure test units.

,,,

Code	Type	D-OD	Press.	kg
275750	DAK 10	10 mm	0-7 bar	0,39
275752	DAK 12	12 mm	0-7 bar	0,41
275754	DAK 14	14 mm	0-7 bar	0,40
275756	DAK 16	16 mm	0-7 bar	0,40

21 | Conduit plug for duct-OD

Conduit plug for fixing on duct-OD with hose safety coupling applicable for duct calibration, duct pressure tests, duct cleaning etc.

,,,

Code	Type	D-OD	Press.	kg
2316512	KRA 20	20 mm	0-7 bar	0,40
23165140	KRA 25	25 mm	0-7 bar	0,46

22 | Connection coupling

Connection coupling for subducts, made of steel, plug-in type, for distribution device DPV 12

,,,

Code	Type	For subduct	To device	Max. Press.	kg
231690	AKS 10	D 10 mm	DPV 12	0-7 bar	0,13
231691	AKS 12	D 12 mm	DPV 13	0-7 bar	0,13
231692	AKS 14	D 14 mm	DPV 14	0-7 bar	0,14
231693	AKS 16	D 16 mm	DPV 15	0-7 bar	0,15
231694	AKS 20	D 20 mm	DPV 16	0-7 bar	0,21

23 | Duct plug

Duct plug of plastic , 0-7 bar, for subducts D 5-20 mm

,,,

Code	Type	For subduct	Max. Press.	kg
272552	ESM 05	D 5 mm	0-7 bar	0,03
272556	ESM 07	D 7 mm	0-7 bar	0,01
272560	ESM 10	D 10 mm	0-7 bar	0,01
272562	ESM 12	D 12 mm	0-7 bar	0,02
272564	ESM 14	D 14 mm	0-7 bar	0,03
272568	ESM 16	D 16 mm	0-7 bar	0,02
272572	ESM 20	D 20 mm	0-7 bar	0,02

24 | Test manometer for conduits

Testing manometer 10 bar, as end section of cable conduits, for high pressure tests, with safety coupling 42 mm. For air distribution devices DPV 1 + DPV 4. Max. air pressure 7 bar. To apply with conduit plugs KRA 20-110.

,,,

Code	Type	For	Together with	Max. Press.								kg
231633	PMK 10	DPV 1+DPV 4	KRA 20-110	0-7 bar								0,70

25 | Test manometer for subducts

Testing manometer 10 bar, as end section of subducts for high pressure tests, with safety coupling NW 7,4. For air distribution devices DPV 12. Max. air pressure 7 bar. To apply with conduit plugs AKS 10-20.

,,,

Code	Type	For	Together with	Max. Press.								kg
231696	PME 10	DPV 12	AKS 10-20	0-7 bar								0,41

26 | Case for accessory

Case for accessory of high pressure test devices, without parts, with 12 shelves as following:

10 cases each 132x82x105 mm
1 case of 168x131x105 mm
1 case of 286x168x105 mm

,,,

Code	Type	Dimension										kg
231698	KZD 6040	600x400x155 mm										4,35

27 | Subduct calibration sets

The calibration sets MKV 0810 and MKV 1116 in conjunction with the accessory micro- transmitter SKS 6 (code-no. 231941) are destined for the calibration of subducts with an internal diameter 8,0 to 16,0 mm. The calibration can be done for single subducts as well as for multi subducts. By the calibration defects or blockages on the subducts can be detected in advance thus a good blowing-in performance can be achieved.

The MKV 0810 set contains two calibres with different diameters for the calibration of subducts with internal diameter 8,0 or 9,8-10,0 mm. The MKV 1116 set contains three different calibres for testing subducts of ID 11,4-16,0 mm. The calibres are easily screwed onto the micro-transmitter and blown through the subducts by air-pressure. The set also contains all essential connectors, reducing nipples as well as a catcher for the micro-transmitter. The catcher has to be used in order to avoid damages to the micro-transmitter. The air-pressure for the calibration has to be limited to max. 4 bars for MKV 0810 and to max. 2 bars for MKV 1116. By applying a higher pressure the micro-transmitter might be damaged by hitting duct blockages or by hard crashing into the catcher at the very end. The set contains the following parts:

MKV 0810 with: each 3 calibre D 6,8 for ID 8,0 / 3 calibre D 8,5 for ID 9,8-10
MKV 1116 with: each 3 calibre D 9,5 / ID 11,4-12 / 3 calibre D 11,0 / ID 15-16 / 3 calibre D 12,5 / ID 15-16.
6 washers to each calibre
5 sponges for each calibre. 1 general catcher and different connectors and duct-reducers
Depending on the duct diameters different air connectors are necessary, see the following tables.

,,,

Code	Type	Device	Subduct-ID	Case	kg
231950	MKV 0810	Calibration set	8-10	180x140x80	1,43
231952	MKV 1116	Calibration set	11,4-16	442x357x151	5,00
231941	SKS 06	Micro transmitter	D 6,5×84	–	0,17
231943	BAT 06	Set of batteries	10 each	–	0,04

28 | Calibration Set for Subducts 10/06

The calibration set MKK 0606 in conjunction with the micro transmitter SKS 04 is foreseen to calibrate subducts with inner diameter D 6.0 mm only. The calibration can be performed for single subducts as well as for multi subducts in buried and protective pipe installed versions. This new calibration set supports the blowing-in of mini- and micro cables on a completely new level since the quality of a sub duct installation can be checked in general.

The set comprises of 3 calibres with protection sponge having a diameter of 4.8 mm, a collecting device for the pipe end, a spare battery cover and 2 spare batteries.

The calibre will be simply unscrewed on the micro transmitter and with the sponge ahead blown-into the pipes using compressed air. The micro transmitter is a precision engineered measuring device, which has to be handled in the civil engineering with special care. Never operate the transmitter without protection sponge, bumper and collecting device fixed at the end of the pipe. Attentions should be paid to max. possible bending radius and air injection pressure – too high air pressure can cause damages on the calibration set.

During backward blowing the enclosed collecting device has to be used or at least a sufficient padding of another collecting device shall be implemented.

Calibration set MKK 0606 including 3 calibres D 4,8 for ID 6,0 mm
20 sponges and collecting device at the pipe end for collection of the calibre
1 Micro Transmitter SKS 04, detection frequency 33 kHz, sensitivity in earth max. 2,0 m
Max. injection pressure 5 bar, 4 bar is sufficient for horizontal routes
Min. bending radius for subducts 175 mm, smaller radius cause unavoidable a blockage
Batteries of the larger micro transmitter SKS 06 are used

,,,

Code	Type	Device	Subduct-ID	Case								kg
231930	MKK 0606	Calibration set	6,0	180x140x80								1,00
231943	BAT 06	Set of batteries	10 pcs.	–								0,04

29 | Detection of multi ducts with average duct in the centre

Multi ducts can be detected in short distances through the average duct of dia. 12×2,0 or 14×2,0 mm laying in the centre. The micro transmitter SKS 06 of diam. 6,4 mm is screwed on the M5 thread of the mini-rod diam. 3 mm. The obtainable pushing length depends on the local condition but is limited anyway by the max. length of the mini rod of 50 m. Using lubricant relieves pushing and pulling back the transmitter. Detection depth in the ground is max. 2 m. The yellow or red mini rod can be used for inserting the micro transmitter.

,,,

Code	Type	Device	Subduct-ID	kg
231941	SKS 06	Micro transmitter	from 8	0,17
231943	BAT 06	Battery set	–	0,04

30 | Locating device for micro transmitter in subducts

Locating device with 2 batteries, for locating blown-in calibres in cable protection pipes or in subducts (micro pipes), as well as for locating non-metallic pipelines and blockages with the pipe coils, yellow or red D 4.5-11. There are the following possible applications:

For detecting blocked calibre in cable conduits or in subducts
Yellow conduit rod with screwed on duct transmitter RD 18 for spot detection
Red conduit rod with screwed on duct transmitter RD 18 for spot detection
Red conduit rod to transmitted by CAT SEN4, for line detection.
Red ORS with CAT SEN4 and screwed on transmitter RD 18 for line and spot detection.

,,,

Code	Type	Frequency	Transmitter	L/W/H mm								kg
231611	CAT4+	33 kHz,	without	255/70/725								2,80

31 | Cable unwinder

Cable unwinder for small drums, even with damaged flanged wheels for electric installation works. Tubular steel construction galvanized. Consisting of: basic frame with 2 rubber coated wheels, one drum shaft D 25 mm with 2 cones of polyamide for hole diameter 25-80 mm.

Collapsible for easy transportation to the site.
Easy movable with the drum through big rubber coated wheels.
For drum-D to 800 and drum widths to 530, drum weight max. 200 kg
As accessory steel tube drum shaft D 50, ball bearings, 2 clamps, for cones see table below.

,,,

Code	Type	Equipment	Shaft	Cones for	kg
320290	KTA 8	Winder as above	D 25	Hole D 25-80	11,60
320292	KTA 8W	Steel tube shaft	D 50	See next line	2,05
315504	ZKP 50-80	Poly-cone (1 each)	D 50	Hole-D 50-80	0,15
3155045	ZKP 50-108	Poly-cone (1 each)	D 50	Hole-D 50-108	0,39

32 | Drum unwinding stand for FOC

Drum unwinding stand for FOC or subduct drums, galvanized. Equipped with a lightweight aluminium shaft D 75 mm with drum shaft securing and 2 clamps.

Sturdy steel construction, hot galvanized, easy dismountable by hand for transportation.
Two crank spindles to lift the stand for unwind cables in any position.
High stability under load even in uneven places.
For drum-D to 1400, and drum width to 900, drum weight max. 500 kg.
As accessory alu-drum shaft D 50, ball bearings, order clamps and cones separately, see table below.
Dimensions mounted: L/W/H 1450/1400/689.

,,,

Code	Type	Equipment	Shaft	Cones for	kg
344355	TRG 1140	Winder as above	D 75	–	96,00
350592	TAK 5013	Alu drum shaft	D 50	–	7,40
315030	KSV 51	Shaft clamps	D 50	–	1,30
315504	ZKP 50-80	Poly-cone (1 each)	D 50	Hole-D 50-80	0,15
3155045	ZKP 50-108	Poly-cone (1 each)	D 50	Hole-D 50-108	0,39

33 | FigarinO the cable basket

FigarinO. The FOC basket is used if the cable is to long to be blown completely with only one blowing machine. When half of the cable is installed in one direction the remaining cable is pushed into the FigarinO with the blowing machine. Out of the FigarinO this part of the cable can be blown uncut in the opposite direction to finish the installation.

A second application is „overblowing” longer cables. Instead of laying these on figure of eight on the floor they can be blown in the FigarinO. After opening the FigarinO the cable ring can be turned around and the cable can be blown-in totally.

Cable Cap.: 4600 m D 4 / 2000 m D 6 / 1200 m D 7,5.
The FigarO replaces laying figure of 8 on the ground, is clean and space saving.
The FigarinO is always placed besides the cable drum.

,,,

Code	Type	Basket-D	For transport									kg
411150	SLK 120	1260	Divisible in the middle.									71,00

34 | Cable lead in bow

Cable bow for pushing-in the cable into the FigarinO with the Minijet

,,,

Code	Type	Equipment	Suitable to	kg
04111521	KEB 120	Cable bow	IntelliJet+MiniJet-FigarinO	3,90
04111523	KEB 120M	Cable bow	Intelli-MicroJet-FigarinO	4,00

35 | Compressor diesel engine

High powered compressors for blowing-in bigger fibre optic cables. Suitable for MiniJet, for duct ID up to 41 mm. Mounted on single axle trailer with height adjustable drawbar, without overrun brake.

Hatz Diesel-engine, 42 kW. Compressor dimension: 4000x1540x1445 mm.
Flow rate 3,8 m³, at 14 bar working pressure
With integrated after cooler and water separator.
Air discharge valve: 2 x G 3/4″

,,,

Code	Type	Air	Press.	D-ID	C-D							kg
960123	M 59	3,8 m³/min.	14 bar	3-16,0	to 10							906,00

36 | Compressor diesel engine

High powered compressors for blowing-in bigger fibre optic cables. Suitable for MiniJet, for duct ID up to 20 mm. Mounted on single axle trailer with height adjustable drawbar, without overrun brake.

Kubota Diesel-engine, 17,9 kW. Compressor dimension: 3245x1260x1330 mm.
Flow rate 1,6 m³, at 14 bar working pressure.
With integrated after cooler and water separator.
Air discharge valve: 2 x G 3/4″ (shown with option EVK 34)

,,,

Code	Type	Compr. air	Press.	D-ID	C-D							kg
960120	M 27	1,60 m³/min.	14 bar	3-16,0	bis 10							600,00

37 | Compressor petrol engine

Compressor with petrol engine and after cooler. For blowing-in fibre optic mini cables, fibres and bundle fibres. Suitable for all MicroJets and for MiniJet P 02. The external after cooler reduces the compressed air temperature approx. 8° C above ambient temperature. The compressor is equipped with a sound absorption cover. It is portable by two pneumatic wheels.

With Honda-petrol engine 16 kW. Dimension: 1080x800x790
Flow rate 1000 l/min. at 15,0 bar working pressure.
With separate after cooler electrical feeded by the compressor. Air discharge valve: 1 x G 3/4″
As accessory see tiltable support for after cooler, table below.

,,,

Code	Type	Air	Press.	D-ID	C-D							kg
960118	MK 17.3	1,0 m³/min.	15 bar	3-12,0	0,8-9,0							206,00

38 | Support for after cooler

Support for the after cooler on compressor MK 17.2. Steel frame hot galvanized. With this the after cooler is fixed safe and rubbery-elastic by four elements.

To transport the compressor in a van the after cooler is tiltable, please mind the total height of approx. 1,10 m. The after cooler can easily be dismounted from the support.