Drum and ring coiling machines for cable Ø 3-40

These types for trade and industry focus on rewinding cables from drum to winding heads. Quick and easy modification also allows each machine to be fitted for winding from drum to drum of Ø 400-1000 mm.

Cable drum and coiling machines for cables and wires. For use in cable stores at distributors, industrial plants etc. Winding and measuring from drum to drum or to coil. Machine in stable steel construction. Drum lifting by hydraulic hand pump. Drum shaft for bores from 60 mm with cones clamped by hand. Cable traversing with ball bearings to mount length measuring equipment MZ and M 20-40 / S, moving by hands. Electronic pre-set counter included as standard equipment. Included safety cage with automatic switch-off. Easy displacement through big wheels. Further accessory see below.

The appropriate length measuring equipment can be selected for this device. It is also possible to permanently mount cable cutting equipment to the measuring machines.

These types for trade and industry focus on rewinding cables from drum to winding heads. Quick and easy modification also allows each machine to be fitted for winding from drum to drum of Ø 400-1000 mm.

Cable drum and coiling machines for cables and wires. For use in cable stores at distributors, industrial plants etc. Winding and measuring from drum to drum or to coil. Machine in stable steel construction. Drum lifting by electro-hydraulic pump. Drum shaft for bores from 60 mm with cones clamped by hand. Cable traversing with ball bearings to mount length measuring equipment MZ and M 20-40 / S, moving by hands. Electronic pre-set counter included as standard equipment. Included safety cage with automatic switch-off. Easy displacement through big wheels. Further accessory see below.

The appropriate length measuring equipment can be selected for this device. It is also possible to permanently mount cable cutting equipment to the measuring machines.

Cable and wire length measuring machines with electronic counter for mounting on all cable winding machines and for stationary use. For this the power supply device 323.110 is necessary. Mounted on a spooling machine the power supply comes from the machine. Very robust steel construction. Due to the big perimeter of 1 m high accuracy of ± 0,5 %, accuracy class III at temperature of 5-40°C.

With conformity assessment according to EU Directive 2014/32/EU, Annex MI-009, valid throughout Europe. Conformity assessment procedure with type examination according to module B and product test according to module F. Equipped as standard with 3.5 inch colour touch screen incl. electronic pre-selection counter.

Application of the new EU directive 2014/32/EU (MID) has become compulsory on 1 November 2016 and it has been implemented in German law in the Verification Act (MessEG) as well as the Verification Ordinance (MessEV). Apart from the correct measurement of lengths, the requirements for the recording, confirmability and traceability of the measurements have been tightened considerably. The main change is the demand for permanent and non-corruptible storage of all measurements.

Specifically, the legislator demands that information on each measurement be stored securely, permanently and unchangeably. Apart from the actual length, the date and time of the measurement as well as information about the measuring instrument used are of relevance. All of these data are to be identified by means of an unambiguous and unique identifier, the objective being to ensure continuous traceability of each measurement. This means that machines may only be brought onto the market if they meet these requirements and have been accepted by a conformity assessment body (e.g. German Physical and Technical Institute, PTB, or the verification office) by way of a conformity assessment. The successful assessment of the measuring instruments is confirmed by the declaration of conformity issued by the manufacturer (e.g. Vetter) and is valid throughout Europe.

For companies who wish to sell the cables to third parties in the normal course of business, this means that only length measuring instruments meeting these requirements may be procured in future. The purchaser of a measuring machine with declaration of conformity is obliged to register the measuring machine with the competent verification office (in Germany www.eichamt.de) immediately following the acquisition. Machines with a declaration of conformity from Vetter are deemed duly verified until expiry of the respective nationally regulated verification period. In Germany the rule is that validity of the conformity assessment is of two years. In retail sale the validity is unlimited as long as no seal is damaged or the maximum number of errors permitted in service is not exceeded. Divergent regulations may apply in other countries. These are obtainable from the applicable national laws.

On expiry of the conformity assessment for the above-mentioned reasons, the competent verification office must carry out a reverification. Before this reverification, examination, adjustment and calibration of the measuring machine by trained personnel is recommended.

Thanks to the EU type examination certificate issued by the Federal Institute of Metrology METAS in Switzerland, machines of the new M series from Vetter can be used throughout Europe, irrespective of whether for use as measuring instruments on coiling machines or as a stand-alone solution for individual use. They offer the demanded uniformity, security, transparency and confirmability for buyers and sellers of cables within the European Economic Area. At the same time, the modular concept of the new series also enables use in direct sales or purely internal use and thus rounds off the complete range of applications for cable length measurement.

The Vetter cable measuring machines from the M 20-M60S series correspond to accuracy class III (+/- 0.5 %) ac-cording to EU Directive 2014/32/EU (MID) at temperatures of 5-40 °C with a minimum cable measuring length of 5 m for M machines and 10 m for MZ 20-M60S machines.

 

To confirm the testing of length measuring devices, KDM/KLM/M/MZ, according to ISO 9001 and other QM systems the calibration (KA 001) executed by Vetter is sufficient in most cases. On the other hand the calibration does not replace the EU conformity assessment whenever it comes to commercial sales of cables.

Roller bow for unwinding cables from drum of upper drum stands. For fitting at cable length measuring machines MZ or M. Steel rollers D 25 mm.

Cable or rope hand cutter including fixing plate for mounting on cable length measuring machines M/MZ 20-40.

Cable cutting head, hydraulic for mounting on cable length measuring machines types M, for cutting insulated CU- and AL-cables, not for steel ropes.

Coil winder collapsible, cylindrical, adjustable in width. For fast serving of cable rings. Capacity 100 kg.

Automatic electronic cable traversing unit to DTR 80FH and DTR 100FH. Adjustment return points and cable diameter electronic with key button and rotary switch on the control panel. Incl. cable layering arm VA 20 for sensitive cables.

Automatic measuring device for identify the cable-d in all length measuring machines on cable spooling machines. The electronic cable traversing unit takes over the electronic measured values self-dependent. Manually correction of cable diameter with potentiometer in operator panel is also possible.

Layering-over arm telescopic for traversing sensitive cables on DTR machines

Control arm with nivomat to prevent from damage of Fibre Optic and sensitive CU-cables up to D 12 mm during winding process. Light control arm of aluminium, length approx. 1050 mm, bending radius R 150 mm, with adjustable weights to the winding process. Arm is easy removable for winding of heavier cables.

Laser-Pointer for easy and accurate adjustment of cable traversing on cable winding machines. Fixing on layering arm or length measuring device M/MZ 20-40